Pasma Legal Requirements

PASMA recommends the use of the PASMA Tower Inspection Record, which not only gives a visual indicator of the inspection status of the tower, but also, when attached to the tower and retained after completion, meets the inspection requirements of the Working at Heights Regulations PASMA has created a pocket map and posters explaining the inspection requirements for mobile towers. Inspection protocols, pocket card and poster can be purchased in the online store. A tower with a distance of less than 2 m can fall has different inspection requirements. It must be inspected after assembly and before use; after any event that may have affected its stability or structural integrity and at appropriate intervals, depending on the frequency and conditions of use. The manufacturer, supplier or lessee is required to provide an instruction manual explaining the sequence of installation, including stiffening requirements and the height up to which the tower can be safely erected. This information must be communicated to the person who builds the tower and to the person who supervises the work. While PASMA training is not a legal requirement to work on cell towers, it is a testament to your education. So if it`s a DIY project, you don`t need it. A PASMA certificate is not a legal requirement, but it is highly recommended to obtain this certification as it is required on all reputable construction sites if you want to use PASMA equipment on site. Anyone who needs to assemble, operate, inspect, modify and dismantle mobile access towers, among other things, should be trained on PASMA tower scaffolding. The knowledge you receive from training not only meets legal health and safety requirements, but also allows you to maximize your personal safety and that of your employees.

At 2 Start Ltd we offer a wide range of PASMA training courses that allow us to meet many different needs and requirements. The PASMA courses we offer include: No, there are no specific legal requirements regarding PASMA. However, those who use towers must undergo some form of training before using them. This issue is addressed in Rule Five of the Working at Heights Regulation: “Every employer shall ensure that no person engages in any activity, including organization, planning and supervision, in connection with working at heights or work equipment intended for use in such work, unless the employer is qualified to do so or, if trained, supervised by a competent person. ». It is generally accepted that competence is demonstrated through a combination of education, practical and theoretical knowledge and experience. As the Health & Safety Executive says: “The type of tower chosen must be suitable for the work and must be assembled and dismantled by people trained and competent to do so. Those using tower scaffolding should also be trained in the potential hazards and precautions required during use. “So if an employee uses a tower or low platform, their employer has to arrange training to comply with working at heights regulations, but it doesn`t have to be PASMA, even though it`s the most popular and respected qualification for towers. If you must work with mobile access towers at height, it is important to undergo training so that the devices can be operated safely and effectively while meeting regulatory requirements. In addition, the trainee acquires new skills, PASMA training ensuring that the right safety and accident prevention measures have been put in place within a company. The cost of PASMA training ranges from £170 to £470 for standard PASMA training with 2 Start Ltd, and our off-site courses vary depending on your specific needs. A typical PASMA course starts in the classroom to meet the instructor and other delegates – up to 12 participants can attend a class.

The day begins with a theory such as an introduction to tower components and legal responsibilities. This usually takes a few hours and can be done online for some courses. Once the instructor is sure that the delegates are ready, they take a theoretical evaluation followed by a lunch break. For courses that include a hands-on component, the instructor divides the group into teams that work together to build and use low-level towers or access devices for the instructor to evaluate. PASMA recommends that for pylons where it is possible to fall 2 m or more, you carry out inspections after assembly or substantial modification, before use and after any event that may have affected the stability or structural integrity of the pylons. You must complete and issue the inspection report in accordance with the altitude order requirements. Inspect the tower as often as necessary to ensure safety, but at least every 7 days, and generate a new report each time. PASMA training would be useful for anyone working at altitude with low equipment, which includes ladders. It`s not a legal requirement, but it`s important to work safely and compliantly in every task you perform, which can be guaranteed by complying with PASMA regulations. The Working at Heights Regulations, 2005 state that employers must ensure that their employees receive appropriate training and can prove it if necessary.

A PASMA training certificate would be a good way to demonstrate this. The PASMA training takes place either in an approved training center or on your site and the theoretical part can take place online. The training is organized by a member of the PASMA accredited training. To learn more about PASMA training, including how to book a course, visit pasma.co.uk/training All employers are required by law to ensure that if you use a type of PEMP (Mobile Elevated Work Platform), you are properly trained. It is safer to climb a tower on a slope on floor plates instead of rollers. Even if the tower is on base plates, you may still need to attach the tower to a load-bearing structure or ground anchors to prevent movement. If the slope is steep, you may need to dig it in place to accommodate the base plates on a flat surface. The PASMA certificate is valid for five years, after which you need a refresher course to renew the certificate. This ensures that you are up to date with all policies. Access Plus are IPAF and PASMA accredited centres and we offer all their courses. Boss Training is accredited by PASMA and is able to issue PASMA cards and certificates of competency to those who successfully complete the training. Only registered PASMA training centers can deliver accredited courses and issue real PASMA certificates and tickets.

Never use the adjustable feet of a mobile tower to gain height. The sole purpose of adjustable feet is to level the tower on uneven or sloping surfaces. At least one adjustable leg should always be on a minimum extension. PASMA training focuses on the use of mobile access towers, which are often used on construction sites. In our courses, participants will learn how to work on mobile access towers at height and provide you with the skills and knowledge you need to pass your test and operate towers safely. PASMA stands for Prefabricated Access Suppliers and Manufacturers` Association and is a widely recognized certification in the construction industry. All of our PASMA courses are taught by a PASMA approved instructor who will help ensure you have the skills and knowledge you need to safely operate a mobile access tower. The duration of your courses depends on which of our PASMA courses you choose, with some courses taking longer than others. The PASMA qualification comes in the form of a certificate and photo card provided by the Prefabricated Access Suppliers and Manufacturers Association (PASMA) after successfully completing one of our recognized PASMA courses. We offer PASMA training in Portsmouth, Southampton, Reading and Worthing. • Low-level access equipment, such as podium steps There are special courses for each tower configuration and for low-level platforms, so participants must choose the courses that are relevant to them.

Those using tower scaffolding should also be trained in the potential hazards and precautions required during use. The Prefabricated Access Suppliers and Manufacturers Association (PASMA) is an industry association focused on the safe use of equipment when working at heights. Their policies focus on low-lying amenities such as scaffolding towers, towers on stairs, and towers with booms. For all rollers with machines such as elevators or raisin pickers, IPAF is the body for you. Transfer from one tower to another can only take place if the tower is not detached and an appropriate risk assessment has been carried out, which may indicate that ALL of the following special measures will be taken as well as any other measures deemed necessary on the basis of a risk assessment: PASMA training covers everything an employee has to say about safe assembly, Use and management of mobile access towers. It also covers the practicality of using high-level access platforms, including risk assessments and accident prevention, as well as health and safety laws and regulations for the use of high-level access platforms. At 2 Start Training we have a wide range of PASMA training courses here in the UK. All our courses are taught by PASMA certified instructors, and all our students receive a PASMA photo card and certificate upon successful completion of their course. The PASMA training courses we offer include: It`s simple: if you don`t have a copy of the current user manual, you won`t be able to assemble the tower. The instructions for use of PASMA manufacturer members can be found on their websites or in our manual library. Whatever your needs or current experience, we have PASMA training for you! This PASMA Work at Height Essentials training is for anyone who knows little or nothing about working at heights.